Options: In total, you will need 18 to 22 inputs, so you can use either 2 multiplexers or one multiplexer and a few additional direct inputs (or extended inputs on another, already used multiplexer along with sone other inputs). ![]() So, your GPS will have only a few wires - 4 address bus lines, 2 inputs and GND (+5v can be taken from the LCD screen board or from the common power supply in your cockpit panel). Using just 2 multiplexer boards with RealSimControl and a small LCD screen you can make your GPS that can be either a separate module or just a mask attached to your main panel (as example of this, see the photo of our Baron 58 panel below). Note: You can use it for GNS430 and any other pop-ups, just rename it accordingly).ĭIY GPS module with RealSimControl Interface If you don't want (or can't) to create this "blank" 1x1 png file, you can download it here (right click and save) file for GNS530. If you want your GPS bezel to be blank for all planes, put these 1x1 files into bitmaps folder of X-Plane (don't forget to move or rename the original Garmin_530_2d.png or Garmin_430_2d.png files before adding these !!): "X-Plane_folder/Resources/bitmaps/cockpit/radios/GPS FMS/" If this folder doesn't exist, create it: "./Your_plane/cockpit/radios/GPS FMS/" Garmin_430_2d.png ) and put it in the "GPS FMS/" folder, located inside of your aircraft root folder. In short, you just need to create a small graphics PNG file 1×1 pixel ( named Garmin_530_2d.png or X-Plane 11 allows you to remove all GNS430/530, FMS and G1000 bezels - you can read how to do this on X-Plane developers website. When you use an external "stand-alone" module such as do-it-yourself GNS430/530, or G1000 built into your panel, you don't need their window bezel to be visible on the external LCD screen. How to remove bezels from popup instrument windows in X-Plane 11 Below are the examples of moving GNS530/430 onto a small 7" LCD display and a 19" monitor: Then, open the GPS window in X-Plane 11, undock it and move this window to the second monitor. First, open your display driver configuration tool and place your second monitor in the desired position. You can use a secondary display connected to your X-Plane 11 computer and just move GNS530 onto it. Find to display GPS screen on additional monitor GPS on external monitor in X-Plane 11 Open X-Plane folder and find you favorite airplane folder location (i.e. X-Plane 11\Aircraft\Carenado CT210M_Centurion)Ģ. ![]() If you are using Reality-XP GNS 530, you can find the instructions on how to remove bezel in the RealityXP instructions. The button on the top right corner is somewhat hidden but you can see it in the video. It will ask to replace the default file, say OK.Ĥ. If you are using with default X-Plane 530, you need to download the following file Garmin_530_2d.png (right click and select "Save Link As") and place it "\X-Plane 11\Resources\bitmaps\cockpit\radios\GPS FMS" folder. Manually assign buttons (one time) Please see below screenshots of appropriate mapping.Ī. Click "Reset to defaults for FlightSimBuilder GNS 530" on bottom left side Open X-Plane and select "FlightSimBuilder GNS 530" on top left sideĤ. Place the downloaded file to " X-Plane 11\Resources\joystick configs" folderģ. There are two opions to get the mapping to X-Plane.Ģ. The mapping is maintained in the WASM module since not all 530 functions are available in the controls mapping. IMPORTANT: There will be no bindings showing in MSFS controls screen. ![]() Run Setup, this will install the launcher and create a link on desktop 5 blinks - encoder speed is set to 5)Ĥb (once in Encoder Speed Mode). Exit Encoder Speed Change. The red LED will blink several times indicating the new encoder speed (i.e. ![]() The bottom red LED one the left side of the unit will light up indicating you are in Encoder Speed mode.Ĥa (once in Encoder Speed Mode).Encoder Speed Change. "Right Small Knob Press" hold for 3 seconds. However currently, if you increase beyond 5, X-Plane / MSFS will not be able to read it. This will enable to increase / decrease encoder speed mode on a scale from 1 to 10 (by default it's 5). Menu +/- "Left Encoder Small Knob"Ģc (once in LCD Menu Mode). Cycle through different video inputs (VGA->HDMI) ".v"Ģd (once in LCD Menu Mode). Menu Enter "Left Encoder Press"Ģb (once in LCD Menu Mode). The top red LED one the left side of the unit will light up indicating you are in LCD menu mode.Ģa (once in LCD Menu Mode). If you have FlightSimBuilder 530 v2 (with cables on the back), there are additional functionality available:ġ. Once in flight simulator, you would just undock the GPS unit and move it to the unit screen. The great news is that this is a Plug and Play solution so once you plug your unit to your PC or Mac, it will recognize it as "FlightSimBuilder 530" joystick.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |